|
Product SKUs |
MBD-X7DWA-N
-O | - X7DWA-N
- (Standard Retail Pack)
|
MBD-X7DWA-N
-B | |
|
Physical Stats |
Form Factor | Extended ATX |
Dimensions | 13" x 12" (33.0cm x 31.0cm) |
|
Processor/Cache |
CPU | - Dual 771-pin LGA Sockets
- Supports up to Dual Intel 64-bit Xeonprocessor(s) of the same type below:
- Quad-Core Intel XeonProcessor 5400/5300LV sequence (Harpertown/Clovertown processor)
- up to 3.20 GHz
- Dual-Core Intel Xeon processor 5200/5100 LV sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz
|
System Bus | 1600 / 1333 / 1066 MHz system bus |
|
System Memory |
Memory Capacity | - Eight 240-pin DIMM sockets
- Supports up to 64 GB 800* / 667 / 533 MHz DDR2 ECC FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
- Memory Sparing supported
|
Memory Type | 800* / 667 / 533 MHz FB-DIMM (Fully Buffered DIMM) ECC DDR2 SDRAM 72-bit, 240-pin gold-plated DIMMs |
DIMM Sizes | 512 MB, 1GB, 2GB, 4GB , 8GB** |
Memory Voltage | 1.8 V or 1.5 V |
Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
|
On-Board Devices |
Chipset | - Intel 5400 (Seaburg) chipset
- ESB2
|
SATA | - Intel ESB2 SATA 3.0 Gb/s controller
- RAID 0, 1, 5, 10 support (Windows only)
- RAID 0, 1, 10 support (Linux)
|
IPMI | - Support for Intelligent Platform Management Interface v.2.0 / 1.5
- 200-pin IPMI slot (SIMLP)
- (Optional: AOC-SIMLP-B)
- (Optional: AOC-SIMLP-3) with 3rd LAN support
- NOTE: KVM-over-LAN not supported - there is no DVO signal to the IPMI slot
|
Network Controllers | - Intel 82575EB Dual-Port Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- Intel I/OAT support for fast, scaleable, and reliable networking
|
Super I/O | Winbond 83627HG chip |
Audio | ALC 883 High Definition 7.1 Channel Audio |
|
Input / Output |
Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
|
IDE | - Single EIDE channel supports up to two UDMA IDE devices (IDE-M, IDE-S) including CF(Compact Flash) Card
- Compact Flash (40-pin connector, IDE 1, single channel) slot
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
Floppy | 1x Floppy controller; 1.44 MB |
LAN | 2x RJ45 LAN ports |
USB | - 4x USB rear ports
- 1x USB internal header
- Total 5x USB 2.0 Compliant / 1.1 Compliant
|
Audio | - High Definition 7.1 Channel Audio
- Line-in / Line-out / Microphone ports
|
Keyboard / Mouse | PS/2 keyboard and mouse ports |
Serial Port / Header | - 1x Fast UART 16550 serial port
- 1x Serial header
|
Parallel Port | 1x ECP / EEP parallel port |
Firewire | 2x IEEE 1394 ports (headers) |
|
Chassis ( Optimized for X7DWA-N
) |
Tower / 4 U Rackmount | - CSE-743TQ-865
- CSE-743T-645
|
Important Chassis Notes | - To ensure system stability, a 550W (minimum) ATX power supply
- [4-pin (+12V), 8-pin (+12V) and 24-pin are required]
|
|
Expansion Slots |
PCI-Express | 2x (x16) PCI-e (Gen 2.0) slots |
PCI-X | 2x 64-bit 133MHz PCI-X (3.3V) slots |
PCI | 2x 32-bit PCI (3.3V) slots |
UIO | 1x UIO Slot |
|
System BIOS |
BIOS Type | 8Mb Flash EEPROM with Phoenix BIOS |
BIOS Features | - Plug and Play (PnP)
- DMI 2.3
- PCI 2.2
- ACPI 1.0 / 2.0
- USB Keyboard support
|
|
Management |
Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
Power Configurations | - ACPI Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard wakeup from soft-off
- CPU Fan auto-off in sleep model
- Power-on mode for AC power recovery
- Suspend to RAM ( STR )
|
|
PC Health Monitoring |
Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V Standby, +5V Standby, VBAT, Memory, Chipset Voltages.
- 5-Phase-switching voltage regulator with auto-sense from 0.8375 V - 1.60 V
|
FAN | - Total of eight 4-pin fan headers supporting up to 8 fans
- 8x fans with tachometer status monitoring
- Status monitor for speed control
- Support 3-pin fans (w/ speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x fan connectors
- PC temperature sensing logic
- PECI
- Thermal Monitor 2 (TM2) support
|
LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
|
Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
|
Operating Environment / Compliance |
RoHS | RoHS Compliant 6/6, Pb Free |
Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
|
OS compatibility |
Please see our OS Compatibility Chart |