| |
Product SKUs |
| MBD-X7DAL-E+-O | X7DAL-E+ (Standard Retail Pack) |
| MBD-X7DAL-E+-B | X7DAL-E+ (Bulk Pack) |
| |
Physical Stats |
| Form Factor | ATX |
| Dimensions | 10" x 12" (25.4cm x 30.5cm) |
| |
Processor/Cache |
| CPU | - Dual 771-pin LGA Sockets
- Supports up to two Intel 64-Bit Xeon processor(s) of the same type below:
- Quad-Core Intel XeonProcessor 5400/5300 sequence
- (Harpertown/Clovertown processor) up to 3.16 GHz
- Dual-Core Intel Xeon processor 5200/5100/5000 sequence (Wolfdale)
- (Woodcrest/Dempsey processor) up to 3.40 GHz
|
| System Bus | 1333 / 1066 / 667 MHz system bus |
| Operating System Software | - Supports 64-Bit Operating Systems
- Supports 32-Bit Operating Systems
|
| |
System Memory |
| Memory Capacity | - Six 240-pin DIMM sockets
- Supports up to 24 GB 667 / 533MHz DDR2 ECC FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
- Memory Mirroring supported
|
| Memory Type | 667 / 533 MHz FB-DIMM (Fully Buffered DIMM) DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB, 4 GB |
| Memory Voltage | 1.8 V only |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
| |
On-Board Devices |
| Chipset | - Intel 5000X (GreenCreek) chipset
- MCH + ESB2
|
| SATA | - Intel ESB2 SATA 3.0 Gb/s controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
|
| Network Controllers | - Intel (ESB2/Gilgal) 82563EB Dual-port Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- Intel I/OAT support for fast, scaleable, and reliable networking
|
| Super I/O | Winbond 83627HF chip |
| Clock Generator | ICS932S401EGLF |
| |
Input / Output |
| Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
|
| IDE | - Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S)
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
|
| Floppy | 1x Floppy controller; 1.44 MB, 2.88 MB |
| LAN | 2x RJ45 LAN ports |
| USB | - 4x USB rear ports
- 2x USB internal headers (for 4 ports)
- 8 total USB ports, 2.0 Compliant / 1.1 Compliant
|
| Audio | - Line-in / Line-out / Microphone ports
- 7.1 High Definition audio
|
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Port / Header | - 1x Fast UART 16550 serial port
- 1x Fast UART 16550 serial header
|
| Parallel Port | Parallel Port Header |
| |
Chassis ( Optimized for X7DAL-E+ ) |
| Mid Tower | CSE-733TQ-645 |
| Tower / 4 U Rackmount | - CSE-743TQ-865
- CSE-743T-645 (FAN-0091, CBL-0088 Required)
- CSE-743i-645
- (FAN-0091, CBL-0088 Required)
|
| Important Chassis Notes | To ensure system stability, a 560W (minimum) ATX power supply [4-pin (+12V), 8-pin (+12V) and 24-pin are required] |
| |
Expansion Slots |
| PCI-Express | - 1x (x16) PCI-e slot
- 1x (x4) PCI-e (using x16) slot
|
| PCI-X | 2x 64-bit 133/100MHz PCI-X (3.3V) slots |
| PCI | 2x 32-bit 33MHz PCI (5V) slot |
| UIO | 1x UIO slot |
| |
System BIOS |
| BIOS Type | 8Mb Flash EEPROM with Phoenix BIOS |
| BIOS Features | - Plug and Play (PnP)
- SMBIOS 2.3
- DMI 2.3
- PCI 2.2
- ACPI 1.0
- PCI-X 1.0
- USB Keyboard support
- Hardware BIOS Virus protection
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
- STR (Suspend-to-RAM)
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V Standby & +5V Standby, VBAT
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
| FAN | - Total of six 4-pin fans
- 6x fans with status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 6x Fan Connectors
- I²C temperature sensing logic
- Thermal Monitor 2 (TM2) support
|
| LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
- +5 V Standby Alert LED
|
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5% to 95% (non-condensing)
|
| |
Regulatory |
| FCC | Class B |
0 Artikel
