|
Product SKUs |
MBD-PDSML-LN2+-O | PDSML-LN2+ (Standard Retail Pack) |
MBD-PDSML-LN2+-B | PDSML-LN2+ (Bulk Pack) |
|
Physical Stats |
Form Factor | MicroATX (uATX) |
Dimensions | 9.6" width x 9.6 " length , (24.4cm x 24.4cm), 6 layers |
|
Processor/Cache |
CPU | - Single LGA775 ZIF Socket
- Supports a Quad-Core Intel Xeon 3200 series processor
- Supports a Dual-Core Intel Xeon 3000 series processor
- Supports a Quad-Core Intel® Core?2 Extreme series processor
- Supports an Intel® Core?2 Quad series processor
- Supports an Intel® Core?2 Duo series processor
- Supports an Intel Pentium processor E2000 series
- Supports a Dual-Core Intel Pentium D processor
- Supports an Intel Pentium Extreme Edition processor
- Supports an Intel Pentium 4 processor
- Supports an Intel Celeron processor E1000 series
- Supports an Intel Celeron processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45 nm processor
|
System Bus | 1066 / 800 / 533 MHz system bus |
|
System Memory |
Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
|
Memory Type | DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs |
DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB |
Memory Voltage | 1.8 V only |
|
On-Board Devices |
Chipset | - Intel 3000 (Mukilteo-2) chipset
- ICH7R + Intel® 82573V + Intel® 82573L
|
Serial ATA | - Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
- RAID 0, 1, 5, 10 support (Windows Only)
|
IPMI | 1U support for Intelligent Platform Management Interface v.2.0 (Optional: AOC-1UIPMI-B ) |
Network Controllers | - 1x Intel 82573V Gigabit PCI-Express Ethernet
- 1x Intel 82573L Gigabit PCI-Express Ethernet
- Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
|
VGA | On-board XGI Volari Z7 graphics |
Super I/O | Winbond 83627HG chip |
Clock Generator | CK410 |
|
Input / Output |
Serial ATA | - Four SATA ports (3 Gb/s performance)
- Four SATA hard drives supported
|
IDE | One EIDE channel supports up to two UDMA/IDE devices |
Floppy | 1x Floppy controller; 1.44 MB |
LAN | 2 x RJ45 LAN port |
USB | - 6x USB 2.0 compliant / 1.1 compatible
- 4x internal USB headers
- 2x rear ports
|
VGA | 1x VGA Port |
Keyboard / Mouse | PS/2 keyboard and mouse ports |
Serial Ports | - 1x Fast UART 16550 serial port
- 1x Header
|
|
Chassis ( Optimized for PDSML-LN2+ ) |
1U Chassis | - CSE-512F-260
- CSE-513F-260
- CSE-811i-300
- CSE-811T-300
|
2U Chassis | - CSE-822T-550LP
- CSE-823i-550LP
- CSE-823T-550LP
- CSE-823T-R500LP
- CSE-823TQ-R500LP
|
Mid-Tower | - CSE-733i-450
- CSE-733i-645
- CSE-733T-450
- CSE-733T-645
- CSE-733TQ-645
|
Tower / 4 U Rackmount | - CSE-742i-300
- CSE-742i-420
- CSE-742i-450
- CSE-742i-600
- CSE-742T-650
- CSE-743i-645
|
Important Note | To ensure system stability, a 300W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is recommended. |
|
Expansion Slots |
Universal Slot | - 1 (x8) PCI-Express Slot OR
- 1x 32-bit 33MHz PCI Slot
|
PCI-Express | 1x (x4) PCI-e (using x8) slot |
PCI | 1x 32-bit 33MHz PCI (5V) slot |
|
System BIOS |
BIOS Type | 8Mb Flash EEPROM with Phoenix BIOS |
BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- ACPI 1.0 (limited)
- USB Keyboard support
- SMBIOS 2.3
|
|
Management |
Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
- W83793 H/W Monitor
|
Power Configurations | - ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
- Internal / External Modem Rign-on
|
|
PC Health Monitoring |
Voltage | - Monitors for CPU Cores +1.8V, +3.3V, +5V, ±12V, +5V Standby
- CPU 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
|
FAN | - Total of six 4-pin fan headers
- 6 fans with tachometer monitoring
- Status Monitor with firmware speed control
- Low noise fan speed control
- Status monitor for on/off control
- Supports 3-pin fans (without speed control)
- Pulse Width Modulated (PWM) fan connector
|
Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) support
- PECI
|
LED | - CPU / System Overheat LED
- Standby Power alert LED
|
Other Features | - Chassis Intrusion Detection
- Chassis Intrusion Header
|
|
Operating Environment / Compliance |
RoHS | RoHS Compliant 6/6, Pb Free |
Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
|
OS compatibility |
Please see our OS Compatibility Chart |
|
Regulatory |
FCC | Passed to meet FCC standard requirement |