| |
Product SKUs |
| MBD-PDSMi-LN4+-O | PDSMi-LN4+ (Standard Retail Pack) |
| MBD-PDSMi-LN4+-B | PDSMi-LN4+ (Bulk Pack) |
| |
Physical Stats |
| Form Factor | ATX |
| Dimensions | 12.0" width x 9.6 " length , (30.5cm x 24.4cm), 6 layers |
| |
Processor/Cache |
| CPU | - Single LGA775 ZIF Socket
- Supports a Quad-Core Intel Xeon 3200 series processor
- Supports a Dual-Core Intel Xeon 3000 series processor
- Supports a Quad-Core Intel® Core?2 Extreme series processor
- Supports an Intel® Core?2 Quad series processor
- Supports an Intel® Core?2 Duo series processor
- Supports an Intel Pentium processor E2000 series
- Supports a Dual-Core Intel Pentium D processor
- Supports an Intel Pentium Extreme Edition processor
- Supports an Intel Pentium 4 processor
- Supports an Intel Celeron processor E1000 series
- Supports an Intel Celeron processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45 nm processor
|
| System Bus | 1066 / 800 / 533 MHz system bus |
| |
System Memory |
| Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered ECC / non-ECC DDR2 667/533MHz memory (Dual Channel)
|
| Memory Type | DDR2 667/533MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs |
| DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB |
| Memory Voltage | 1.8 V only |
| |
On-Board Devices |
| Chipset | - Intel 3000 (Mukilteo-2) chipset
- ICH7R + PXH-V + Intel 82573V + Intel 82573L
|
| Serial ATA | - Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
- RAID 0, 1, 5, 10 support (Windows Only)
- Adaptec:
- RAID 0 (Two, three, four drives only)
- RAID 1 (Two hard drives only)
|
| IPMI | 1U support for Intelligent Platform Management Interface v.2.0 (Optional: AOC-IPMI20-E ) |
| Network Controllers | - Dual double-stack ports using 1x Intel® 82573V and 3x Intel® 82573L Gigabit PCI-Express Ethernet Controllers, Four ports total
- Supports 10Base-T, 100Base-TX, 1000BASE-TX, RJ45 output
|
| VGA | On-board XGI Volari Z7 graphics |
| Super I/O | Winbond 83627HG chip |
| Clock Generator | CK410 |
| |
Input / Output |
| Serial ATA | - Four SATA ports (3 Gb/s performance)
- Four SATA hard drives supported
|
| IDE | - One EIDE channel supports up to two UDMA/IDE devices
- IDE Master / Slave 2 ports
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- White Connector for Compact Flash (CF, 40-pin IDE connector) card only
|
| Floppy | 1x Floppy controller; 1.44 MB |
| LAN | 4x RJ45 LAN ports |
| USB | - USB 2.0 compliant / 1.1 compatible
- 4x internal USB headers
- 2x rear ports
|
| VGA | 1x VGA Port |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Ports | - 1x Fast UART 16550 serial port
- 1x Header
|
| Parallel Port | 1x ECP / EEP Parallel Header |
| |
Chassis ( Optimized for PDSMi-LN4+ ) |
| 4U / Tower | SC743i-645 |
| Important Note | - To ensure system stability, a ATX power supply w/ 4A (minimum) on 5V Standby is required
- Only this Supermicro 1U chassis is recommended for this Network Building Block Solution
|
| |
Expansion Slots |
| PCI-X | 1x 64-bit PCI-X 133MHz slot |
| PCI | 1x 32-bit 33MHz PCI (5V) slot |
| Note | Riser Card required for 1U systems |
| |
System BIOS |
| BIOS Type | 8Mb Flash EEPROM with Phoenix BIOS |
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- SMBIOS 2.3
- USB Keyboard support
|
| |
Management |
| Software | - Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
- W83793 H/W Monitor
|
| Power Configurations | - ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
- Internal / External Modem Rign-on
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.5V, +3.3V, +5, ±12V, +5V Standby
- CPU core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio
|
| FAN | - Fan Speed Control
- 6x 4-pin fan headers
- 6x fans with tachometer monitoring
- Status Monitor with firmware speed control
- Low noise fan speed control
- Status monitor for on/off control
- Supports 3-pin fans (without speed control)
- Pulse Width Modulated (PWM) fan connector
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED | - CPU / System Overheat LED
- Standby Power alert LED
|
| Other Features | - Chassis Intrusion Detection
- Chassis Intrusion Header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
| |
OS compatibility |
| Please see our OS Compatibility Chart |
| |
Regulatory |
| FCC | Passed to meet FCC standard requirement |
0 Artikel
