| |
Product SKUs |
| MBD-C2SBA+
-O | - C2SBA+
- (Standard Retail Pack)
|
| MBD-C2SBA+
-B | |
| |
Physical Stats |
| Form Factor | ATX |
| Dimensions | 12.0" x 9.6 ", (30.5cm x 24.4cm) |
| |
Processor/Cache |
| CPU | - Single LGA775 ZIF Socket
- Supports Intel® Core?2 Quad Q9000/Q8000/Q6000 series
- Supports Intel® Core?2 Duo E8000/E7000/E6000/E4000 series
- Supports Intel Pentium E5000/E2000 series
- Supports Intel Celeron E1000 and 400 series
|
| System Bus | 1333 / 1066 / 800 MHz system bus |
| |
System Memory |
| Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered, non-ECC DDR2 800/667MHz memory (Dual Channel)
|
| Memory Type | DDR2 800/667MHz unbuffered, non-ECC SDRAM, 240-pin gold-plated DIMMs |
| DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB |
| Memory Voltage | 1.8 V only |
| |
On-Board Devices |
| Chipset | |
| Serial ATA | Intel® ICH9 SATA2 (3 Gbps) controller built-in |
| Network Controllers | - 1 x Intel® 82566 Gigabit Ethernet
- Supports 10 BASE-T, 100 BASE-TX, and 1000 BASE-T with RJ45 output
|
| Audio | High Definition 7.1 Channel Audio |
| Video | On board graphics |
| Super I/O | Winbond 83627DHG chip |
| Clock Generator | CK505 |
| |
Input / Output |
| Serial ATA | - Four Serial ATA ports (3Gbps)
- Four SATA hard drives supported
|
| IDE | - Two EIDE channel supports up to four UDMA IDE devices
- ITE 8212F chipset - Rev 1.2 or earlier
- ITE 8211F chipset - Rev 1.2A or later
|
| Floppy | 1x Floppy controller; 1.44 MB |
| LAN | 1x RJ45 LAN port |
| USB | - 12x USB 2.0 / 1.1 compatible
- 6 rear + 2 Type A connectors + 2 headers (4 ports)
|
| Audio | - High Definition 7.1 Channel Audio
- Line-in / Line-out / Microphone ports
|
| VGA | On board VGA port |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Ports | - 1x Fast UART 16550 serial port
- 1x Serial Header
|
| Parallel Port | 1x ECP / EEP Parallel Port |
| |
Chassis ( Optimized for C2SBA+
) |
| Mid-Tower | - CSE-733E-465B
- CSE-733i-450
- CSE-733i-465B
- CSE-733i-645
- CSE-733T-450
- CSE-733T-465B
- CSE-733T-645
- CSE-733TQ-465B
|
| Tower / 4 U Rackmount | CSE-742i-450 |
| Important Note | To ensure system stability, a 420W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is required. |
| |
Expansion Slots |
| PCI-Express | - 1x (x16) PCI-e slot
- 1x (x4) PCI-e slot (using x8 slot)
- 1 (x1) PCI-e slot
|
| PCI | 3x 32-bit 33MHz PCI (5V) slots |
| |
System BIOS |
| BIOS Type | 16Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3
- PCI 2.2
- ACPI 1.0 / 2.0
- USB Keyboard support
- SMBIOS 2.3
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
- Hardware monitor in W83627DHF (PECI support)
|
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard wakeup from soft-off
- Power-on mode control for AC power recovery
- Internal / External modem remote ring-on
- Suspend to RAM (STR)
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V/+5V Standby, VBAT
- CPU core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio (Only available if CPU is supported)
|
| FAN | - Total of five 4-pin fan headers
- 3 x fans with tachometer monitoring
- Status monitor for speed control
- Status Monitor for on / off control
- Support 3-pin PWM fans (without speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan conn.
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) Support
- PECI
|
| LED | - CPU / System Overheat LED
- Standby power alert LED
|
| Other Features | - Chassis intrusion Detection
- Chassis intrusion Header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
| |
OS compatibility |
| Please see our OS Compatibility Chart |
| |
Regulatory |
| FCC | Class B |
0 Artikel
