| |
Product SKUs |
| MBD-X7DCX-O | X7DCX(Standard Retail Pack) |
| MBD-X7DCX-B | X7DCX(Bulk Pack) |
| |
Physical Stats |
| Form Factor | Extended ATX |
| Dimensions | 12" x 13.05" (30.5cm x 33.2cm) |
| |
Processor/Cache |
| CPU | - Dual 771-pin LGA Sockets
- Supports up to Dual Intel 64-bit Xeonprocessor(s) of the same type below:
- Quad-Core Intel XeonProcessor 5400/5300 sequence (Harpertown/Clovertown processor) up to 3.16 GHz
- Dual-Core Intel Xeon processor 5200/5100 sequence (Wolfdale/Woodcrest processor) up to 3.40 GHz
|
| Operating System Software | - Supports 64-Bit Operating Systems
- Supports 32-Bit Operating Systems
|
| |
System Memory |
| Memory Capacity | - Six 240-pin DIMM sockets
- Supports up to 48 GB 667/533 MHz DDR2 ECC registered SDRAM
- Dual channel memory bus
- Memory must be populated in pairs
|
| Memory Type | 667/533 MHz Register DDR2 ECC SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | 512MB, 1GB, 2GB, 4GB, 8GB** |
| Memory Voltage | 1.8 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
On-Board Devices |
| Chipset | - Intel 5100 (San Clemente) chipset
- Intel ICH9R
|
| SATA | - Intel ICH9R SB SATA-2 controller
- RAID 0, 1, 5, 10 support (Windows only)
- RAID 0, 1, 10 support (Linux)
|
| IPMI | - Support for Intelligent Platform Management Interface v.2.0 / 1.5
- 200-pin IPMI slot (SIMSO(+))
- (Optional: AOC-SIMSO(+))
- For dedicated LAN, cable CBL-0177L must be used (cable sold separately)
|
| Network Controllers | - Dual Intel® 82573V/L Single Port Gigabit Ethernet Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
|
| Graphics | XGI Z9s with 32 MB of DDR2 memory |
| Super I/O | Winbond 83627DHG chip |
| Clock Generator | ICS9LPR501 chip |
| |
Input / Output |
| Serial ATA | - 6 Serial ATA ports
- 6 SATA hard drives supported
|
| IDE | - Single EIDE channel supports up to two UDMA IDE devices(IDE-M, IDE-S) including CF card
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- Compact Flash (40-pin connector, IDE 1, single channel) slot
|
| Floppy | 1x Floppy controller; 1.44 MB |
| LAN | 2x RJ45 LAN ports |
| USB | - 2 rear + 2 Type A connectors + 2 headers (4 Ports)
- 8 total USB ports, 2.0 Compliantt
|
| VGA | 1x VGA Port |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Port / Header | - 1x Fast UART 16550 serial port
- 1x Header
|
| |
Chassis ( Optimized for X7DCX) |
| Tower / 4 U Rackmount | - CSE-745TQ-R800
- CSE-745TQ-800
- CSE-743TQ-R760
- CSE-743T-R760
- CSE-743i-R760
- CSE-743T-650
- CSE-743i-650
- CSE-743T-645 (FAN-0091 Required)
- CSE-743i-645 (FAN-0091 Required)
|
| Important Chassis Notes | To ensure system stability, a 500W (minimum) ATX power supply [4-pin (+12V), 8-pin (+12V) and 24-pin are required] |
| |
Expansion Slots |
| PCI-Express | - 5 (x8) PCI-e (1 in x16) slots
- 1x (x4) PCI-e (using x8) slot
|
| PCI | 1x 32-bit 33MHz PCI (5V) slots |
| |
System BIOS |
| BIOS Type | 16Mb SPI Flash with Phoenix BIOS |
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3
- PCI 2.2
- ACPI 1.0/2.0/3.0
- USB Keyboard support
- Hardware BIOS Virus protection
- SMBIOS 2.3
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations | - ACPI Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- CPU Fan auto-off in sleep mode
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU cores,+1.5 V, +3.3 V, +5 V, ±12 V, +5 Stdby, VBAT
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.60V
|
| FAN | - Eight 4-pin fan headers
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Support for 3-pins (w speed control)
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- PSU I²C temperature sensing logic
|
| LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
- +5 V Standby alert LED
|
| Other Features | - Chassis Intrusion Detection
- Chassis Intrusion Header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
0 Artikel
