|
Product SKUs |
MBD-X7SB4
-O | - X7SB4
- (Standard Retail Pack)
|
MBD-X7SB4
-B | |
|
Physical Stats |
Form Factor | ATX |
Dimensions | 12" x 9.6 ", (30.48cm x 24.38 cm) |
|
Processor/Cache |
CPU | - Single LGA775 ZIF Socket
- Supports Quad-Core Intel Xeon X3300/X3200 series
- Supports Dual-Core Intel Xeon E3100/3000 series
- Supports Intel Xeon processor L3360 and L3110 series
- Supports Intel® Core?2 Quad Q9000/Q8000/Q6000 series
- Supports Intel® Core?2 Duo E8000/E7000/E6000/E4000 series
- Supports Intel Pentium E5000/E2000 series
- Supports Intel Celeron E1000 and 400 series
- NOTE: Intel Xeon processor L3014 requires an LGA771 socket and is not supported.
|
System Bus | 1333 / 1066 / 800 MHz system bus |
|
System Memory |
Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of memory (Dual Channel)
|
Memory Type | DDR2 800/667 MHz unbuffered ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs |
DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB |
Memory Voltage | 1.8 V only |
|
On-Board Devices |
Chipset | - Intel 3210 chipset
- ICH9R + PXH + Intel 82573V + Intel 82573L
|
Serial ATA | - Intel® ICH9R SATA2 (3 Gbps) controller built-in
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
|
SCSI | - Adaptec AIC-7901 Single-channel U320 SCSI Controller
- Host RAID 0, 1, 10 Supported
|
SCSI ZCR | - Support for Zero-Channel RAID
- Optional: (card NOT included)
|
IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN & optional KVM over LAN support
- 200-pin IPMI slot
- (Optional: AOC-SIMLC-HTC)
- (Optional: AOC-SIM1U+)-KVM-over-LAN support
- NOTE: Must use Dedicated LAN for KVM-over-LAN function
|
Network Controllers | - 2x Single-port Gigabit PCI-Express Ethernet Controllers
- Intel 82573V + Intel 82573L
- Supports 10BASE-T, 100BASE-T, 1000BASE-T, RJ45 output
|
VGA | On-board ATI ES1000 (32MB) graphics |
Super I/O | Winbond W83627HG-AW chip |
Clock Generator | CK505 |
|
Input / Output |
Serial ATA | - Six Serial ATA ports (3 Gb/s performance)
- Six SATA hard drives supported
|
Floppy | 1x Floppy controller; 1.44 MB |
LAN | 2x RJ45 LAN ports |
USB | - Up to 7x USB 2.0 / 1.1 compliant ports
- 2x rear ports
- 2 internal headers + 1 on-board
|
VGA | 1x VGA port |
Keyboard / Mouse | PS/2 keyboard and mouse ports |
Serial Ports | - 1x Fast UART 16550 serial port
- 1x internal header
|
|
Chassis ( Optimized for X7SB4
) |
2U Chassis | - CSE-823S-550LP
- CSE-823S-R500LP
|
3U Chassis | CSE-833S-550 |
Mid-Tower | - CSE-733E-465B
- CSE-733i-465B
- CSE-733T-465B
- CSE-733TQ-465B
|
Tower / 4 U Rackmount | - CSE-742S-450
- CSE-743TQ-865B
|
Important Note | For a general system, a 420W (minimum) ATX12V power supply [8-pin +12V AND 24-pin is recommended to assure system stability]. |
|
Expansion Slots |
PCI-Express | - 1x (x8) PCI-e slot
- 1x (x4) PCI-e slot
|
PCI-X | - 2x 64 bit PCI-X 133 MHz slot
- 2x 64 bit PCI-X 100 MHz slot
|
|
System BIOS |
BIOS Type | 16Mb Flash EEPROM with Phoenix BIOS |
BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0/2.0
- SMBIOS 2.3
- USB Keyboard support
|
|
Management |
Software | - SuperDoctor® III
- Watch Dog
- NMI
- H/W Monitor in W83627DHF(PECI support)
|
Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard wakeup from soft-off
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
|
|
PC Health Monitoring |
Voltage | - Monitors for CPU cores ( +1.8 V, +3.3 V, +5, ±12 V, +3.3 V Standby, +5 V Standby, VBAT, HT, Memory, chipset)
- CPU core 4-Phase-switching voltage regulator with auto-sense from 0.3750V-1.6000V
- Adjustable CPU clock frequency ratio (Only available if CPU is supported)
|
FAN | - Total of six 4-pin fan headers
- 6x fans with tachometer monitoring
- Status Monitor with firmware / software speed control
- Status monitor for on/off control
- Support 3-pin and 4-pin Fan speed control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
|
Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) Support
- PECI
|
LED | - CPU / System Overheat LED
- Supsend-State Indicator LED
- +5 V Standby alert LED
|
Other Features | - Chassis intrusion detection
- Chassis intrusion header
|
|
Operating Environment / Compliance |
RoHS | RoHS Compliant 6/6, Pb Free |
Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
|
OS compatibility |
Please see our OS Compatibility Chart |