| |
Product SKUs |
| SYS-1026TT-IBQF | SuperServer 1026TT-IBQF (Black) |
| |
Motherboards |
| Super X8DTT-IBQF + Super X8DTT-IBQF |
| |
Processor/Cache |
| CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel 64-Bit Xeon processor(s) of the same type below:
- Intel Xeon processor X5600/E5600/L5600 Series (Westmere) 40 W - 130 W
- Intel Xeon processor X5500/E5500/L5500 Series (Nehalem-EP) 38 W - 95 W
|
| QPI | Up to 6.4 GT/s |
| |
System Memory |
| Memory Capacity | - 12x 240-pin DIMM sockets
- Supports up to 192 GB** 1333 / 1066 / 800 MHz DDR3 ECC registered memory
- Supports up to 48 GB 1333 / 1066 / 800 MHz DDR3 ECC / Non ECC unbuffered memory
- Memory Mirroring supported
|
| Memory Type | 1333 / 1066 / 800MHz ECC registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | - 1GB, 2GB, 4GB
- , 8 GB**
- , 16 GB**
|
| Memory Voltage | 1.5 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
| |
On-board Devices (per Node) |
| Infiniband | Mellanox ConnectX-2 QDR Infiniband 40 Gb/s Controller |
| Chipset | - Intel 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
|
| SATA | - Intel ICH10R SATA 3.0 Gb/s controller
- RAID 0, 1, 5, 10 support
|
| Network Controllers | - Intel 82576 Dual-Port Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- Intel I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics | Matrox G200eW 16 MB DDR2 |
| Super I/O | Winbond W83527HG chip |
| Clock Generator | 932S421 chip |
| |
Input / Output (per Node) |
| Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
|
| LAN | - 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB | - 2x rear + 1x header (2x Ports)
- 4 total USB ports, 2.0 Compliant / 1.1 Compliant
|
| VGA | 1x VGA Port |
| Serial Port | 1x Fast UART 16550 serial port |
| Infiniband | 1x External QSFP Infiniband Connector |
| |
System BIOS (per Node) |
| BIOS Type | 32Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
Chassis |
| Form Factor | 1U Rackmount |
| Model | CSE-809TQ-1200B |
| |
Dimensions |
| Height | 1.7" (43 mm) |
| Width | 17.2" (437mm) |
| Depth | 27.75" (705 mm) |
| Gross Weight | 40 lbs (18.1 kg) |
| Available Colors | Black |
| |
Front Panel (per Node) |
| Buttons | - Power On/Off button
- System Reset button
|
| LEDs | - Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat LED
|
| |
Expansion Slots (per Node) |
| PCI-Express | 1x (x16) PCI-E (Low-Profile) |
| |
Drive Bays (per Node) |
| Hot-Swap | 4x 2.5" SATA Hot-swap drive bays |
| |
SATA Backplane |
| 1U SATA Backplane |
| |
System Cooling |
| Fans | 6x Cooling Fans |
| |
Power Supply |
| 1200 W high-efficiency power supply with PMBus |
| AC Input | - 1000 W Output @ 100-140 V, 11.5-8 A, 50-60 Hz
- 1200 W Output @ 180-240 V, 8-5.5 A, 50-60 Hz
|
| DC Output | - 1000 W: +12 V / 83 A; +5 V sb / 4 A
- 1200 W: +12 V / 100 A; +5V sb / 4 A
|
| Certification | Gold Certified |
| |
Management |
| Software | - IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Power-on mode for AC power recovery
|
| |
PC Health Monitoring |
| CPU | - Monitors for CPU cores,+1.5 V, +3.3 V, +5 V, +12 V, +5 Stdby, +3.3 Stdby, VBAT, Memory voltages.
- CPU core 6-Phase-switching voltage regulator
|
| FAN | - Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I²C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED | - Power Fail / Overheat LED
- Supsend-State Indicator LED
- UID LED
|
| Other Features | SDDC Support |
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
0 Articoli
