| |
Product SKUs |
| SYS-6026TT-H6RF | SuperServer 6026TT-H6RF (Black) |
| |
Motherboard |
| 4x Super X8DTT-HEF+ |
| |
Processor/Cache |
| CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel 64-Bit Xeon processor(s) of the same type below:
- Intel Xeon processor X5600/E5600/L5600 Series (Westmere) 40 W - 95 W
- Intel Xeon processor X5500/E5500/L5500 Series (Nehalem-EP) 38 W - 95 W
|
| QPI | Up to 6.4 GT/s |
| |
System Memory |
| Memory Capacity | - 12x 240-pin DIMM sockets
- Supports up to 192 GB** 1333 / 1066 / 800 MHz DDR3 ECC registered memory
- Supports up to 48 GB 1333 / 1066 / 800 MHz DDR3 ECC / Non ECC unbuffered memory
- Memory Mirroring supported
|
| Memory Type | 1333 / 1066 / 800MHz ECC registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | - 1GB, 2GB, 4GB
- , 8 GB**
- , 16 GB**
|
| Memory Voltage | 1.5 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
| |
On-board Devices (per Node) |
| Chipset | - Intel 5520 (Tylersburg) chipset
- ICH10R
|
| SAS | - LSI 6 Gb/s SAS 2108 w/ Hardware RAID support via BPN-ADP-SAS-2-H6iR
- RAID 0, 1, 5 support
|
| IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM over LAN support
- Nuvoton WPCM450 BMC
|
| Network Controllers | - Dual Intel 82574L Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics | Matrox G200eW |
| Super I/O | Winbond W83527HG chip |
| Clock Generator | 932S421 chip |
| |
Input / Output (per Node) |
| SAS | 3 SAS hard drives supported |
| LAN | - 2x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB | - 2 rear
- 2 total USB ports, 2.0 Compliant / 1.1 Compliant
|
| VGA | 1x VGA Port |
| Serial Port | 1x Fast UART 16550 serial port |
| |
System BIOS (per Node) |
| BIOS Type | 32Mb SPI Flash EEPROM with AMI BIOS |
| BIOS Features | - Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
Chassis |
| Form Factor | 2U Rackmount |
| Model | CSE-827HQ-R1400B |
| |
Dimensions |
| Height | 3.5" (89mm) |
| Width | 17.2" (437mm) |
| Depth | 28.5" (724 mm) |
| Gross Weight | 85 lbs (38.6kg) |
| Available Colors | Black |
| |
Front Panel (per Node) |
| Buttons | - Power On/Off button
- UID button
|
| LEDs | - Power LED (on power button)
- Network activity LED
- System Overheat/fan fail/power fail LED
- UID LED (on UID button)
|
| |
Expansion Slots (per Node) |
| PCI-Express | 1x (x8) PCI-E 2.0 via riser card (Low-Profile) |
| |
Drive Bays (per Node) |
| Hot-Swap | 3x 3.5" hot-swap SAS drive bays |
| |
Hard Drive Backplane |
| 2U Hard drive Backplane |
| |
System Cooling |
| Fans | 4x 8cm PWM Cooling Fans with Optimal fan speed control |
| |
Power Supply |
| 1400 W high-efficiency (1+1) redundant power supply with PMBus |
| AC Input | - 1100 W Output @ 100-140 V, 13.5-9.5 A, 50-60 Hz
- 1400 W Output @ 180-240 V, 9.5-7.0 A, 50-60 Hz
|
| DC Output | - 1100 W: +12 V / 92 A; +5V sb / 4 A
- 1400 W: +12 V / 116 A; +5 V sb / 4 A
|
| With Distributor | - +5 V: 30 A
- +3.3V: 24 A
- -12V: 0.6 A
|
| Certification | Gold Certified |
| |
PC Health Monitoring |
| CPU | - Monitors for CPU cores,+1.5 V, +3.3 V, +5 V, +12 V, +5 Stdby, +3.3 Stdby, VBAT, Memory voltages.
- CPU core 6-Phase-switching voltage regulator
|
| FAN | - Total of four 4-pin PWM fans
- 4x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 4x Fan Connectors
- PSU I²C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
|
| LED | - Power Fail / Overheat LED
- Supsend-State Indicator LED
- UID LED
|
| Other Features | SDDC Support |
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5% to 95% (non-condensing)
|
0 Articoli
