| |
Product SKUs |
| SYS-2026T-6RFT+ | SuperServer 2026T-6RFT+ (Black) |
| |
Motherboard |
| Super X8DTU-6TF+ |
| |
Processor/Cache |
| CPU | - Dual 1366-pin LGA Sockets
- Supports up to two Intel 64-Bit Xeon processor(s) of the same type below:
- Intel Xeon processor X5600/E5600/L5600 Series (Westmere) 40 W - 130 W
- Intel Xeon processor X5500/E5500/L5500 Series (Nehalem-EP) 38 W - 95 W
|
| QPI | Up to 6.4 GT/s |
| |
System Memory |
| Memory Capacity | - 18x 240-pin DIMM sockets
- Supports up to 288 GB 1333 / 1066 / 800 MHz DDR3 ECC registered memory
- Supports up to 48 GB 1333 / 1066 / 800 MHz DDR3 ECC / Non ECC unbuffered memory
- Memory Mirroring supported
|
| Memory Type | 1333 / 1066 / 800MHz ECC registered / ECC or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs |
| DIMM Sizes | - 1GB, 2GB, 4GB
- , 8 GB
- , 16 GB
|
| Memory Voltage | 1.5 V / 1.35 V |
| Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel x4 and x8 Single Device Data Correction (SDDC)
|
| Note: | This board does not support LRDIMM memory. |
| |
On-Board Devices |
| Chipset | - Intel 5520 (Tylersburg) chipset
- ICH10R
|
| SAS | - LSI 6 Gb/s SAS 2108 w/ Hardware RAID support
- RAID 0, 1, 5, 6, 10, 50, 60 support
- BBU (Battery Backup Unit) Extension Kit
|
| SATA | - Intel ICH10R SATA 3.0 Gb/s controller
- RAID 0, 1, 5, 10 support
|
| Network Controllers | - Intel 82599EB 10 Gigabit Ethernet Controller with 2 SFP+ interfaces
- Intel 82576 Dual-Port Gigabit Ethernet controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T; RJ45 output
- Intel I/OAT 3 support for fast, scaleable, and reliable networking
- VMDq support for better performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
| Graphics | Matrox G200eW |
| Super I/O | Winbond 83827HF chip |
| |
Input / Output |
| Serial ATA | - Six Serial ATA ports
- Six SATA hard drives supported
|
| LAN | - 2x RJ45 LAN ports
- 2x SFP+ LAN port
- 1x RJ45 Dedicated IPMI LAN port
|
| USB | - 2x USB rear ports
- 1x USB on-board
- 2x USB internal headers
- Total 5x USB 2.0 Compliant
|
| VGA | 1x VGA Port |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Port / Header | - 1x Fast UART 16550 serial port
- 1x Fast UART 16550 serial header (Option)
|
| |
Chassis |
| Form Factor | 2U Rackmount |
| Model | CSE-219A-R920UB |
| |
Dimensions |
| Height | 3.5" (89mm) |
| Width | 17.2" (437mm) |
| Depth | 27.75" (705 mm) |
| Gross Weight | 55 lbs (24.9kg) |
| Available Colors | Black |
| |
Front Panel |
| Buttons | - Power On/Off button
- System Reset button
|
| LEDs | - Power LED
- Hard drive activity LED
- 2x Network activity LEDs
- System Overheat / Fan Failure LED
- Power fail LED
|
| Ports | 2x USB Ports |
| |
Expansion Slots |
| PCI-Express | - 2x (x8) PCI-E 2.0 slots (Left Slot)
- 1x (x4) PCI-E 2.0 (in x8 slot Low-Profile - 5.5" depth) (Right Slot)
- UIO AoC Compatibility Matrix
|
| |
Drive Bays |
| Hot-Swap | 16x 2.5" SAS / SATA Hot-swap drive trays * (see note below) |
| |
Peripheral Drives |
| DVD-ROM | Slim 8x DVD, 24x CD, DVD-ROM drive |
| |
Backplane |
| 2U SAS/SATA Backplane |
| |
System Cooling |
| Fans | 4x 80 mm 6300 RPM fans |
| Shroud | 1x Air Shroud |
| |
Power Supply with Power Distributor |
| 920 W high-efficiency (94%+) AC-DC Redundant power supplies with PMBus and I²C |
| AC Input | 100-240 V, 50-60 Hz, 11-4.5 A |
| DC Output | - 4 A @ +5 V Standby
- 75 A @ +12 V
|
| Certification | Platinum Certified |
| |
PC Health Monitoring |
| CPU | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, 12V, +3.3V Standby, +5V Standby, VBAT, Memory, Chipset Voltages.
- 6-Phase-switching voltage regulator
|
| FAN | - Total of eight fan headers supporting up to 8 fans
- Eight 4-pin fan headers
- 8x fans with tachometer status monitoring
- Supports 3-pin fans (w/o speed control)
- Low noise fan speed control
|
| Temperature | - Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
|
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
0 Articoli
