| |
Product SKUs |
| MBD-PDSBA-O | PDSBA (Standard Retail Pack) |
| MBD-PDSBA-B | PDSBA (Bulk Pack) |
| |
Physical Stats |
| Form Factor | ATX |
| Dimensions | 11.5" x 9.5 ", (29.2cm x 24.0cm) |
| |
Processor/Cache |
| CPU | - Single LGA775 ZIF Socket
- Supports a Dual-Core Intel® Xeon® 3000 Series processor
- Supports an Intel® Core?2 Duo Series processor
- Supports a Dual-Core Intel Pentium D processor
- Supports an Intel Pentium 4 processor
- Supports an Intel Celeron D processor
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45 nm processor
|
| System Bus | 1066 / 800 / 533 MHz system bus |
| |
System Memory |
| Memory Capacity | - Four 240-pin DIMM sockets
- Supports up to 8 GB of unbuffered, non-ECC DDR2 800/667/533MHz memory (Single / Dual Channel)
|
| Memory Type | DDR2 800/667/533MHz unbuffered, non-ECC SDRAM, 240-pin gold-plated DIMMs |
| DIMM Sizes | 256 MB, 512 MB, 1 GB, 2 GB |
| Memory Voltage | 1.8 V only |
| |
On-Board Devices |
| Chipset | - Intel G965
- ICH8 + Intel® 82573L
|
| Serial ATA | Intel® ICH8 SATA (3Gbps) controller built-in |
| Network Controllers | - Intel® 82573L (Single Port) Gigabit PCI-Express Ethernet
- Supports 10BASE-T, 100/1000BASE-TX, RJ45 output
|
| Graphics | On-chip integrated gfx graphics core |
| Audio | Realtek high quality 7.1 channel audio |
| Super I/O | Winbond 83627HG chip, STM (Trust Platform Module) controller |
| Clock Generator | ICS9LPRS511 |
| TPM | ST19WP18 |
| |
Input / Output |
| Serial ATA | - Four Serial ATA ports (3Gbps)
- Four SATA hard drives supported
|
| Floppy | 1x Floppy controller; 1.44 MB |
| LAN | 1x RJ45 LAN port |
| USB | - 6x USB 2.0 compliant external ports
- 2x internal headers supporting up to 4 ports (USB 2.0 Compliant)
|
| VGA | 1x VGA port |
| Audio | 1x Line In / Front L & R / Center & Sub-Woofer/ Surround L & R / Side Surround L & R / Line Out / Microphone ports |
| Keyboard / Mouse | PS/2 keyboard and mouse ports |
| Serial Ports | - 1x Fast UART 16550 serial port
- 1x Serial Header
|
| Parallel Port | 1x ECP / EEP Parallel Port |
| |
Chassis ( Optimized for PDSBA ) |
| Mid-Tower | - CSE-733i-450
- CSE-733i-645
- CSE-733T-450
- CSE-733T-645
|
| Tower / 4 U Rackmount | CSE-742i-450 |
| Important Note | To ensure system stability, a 450W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is required. |
| |
Expansion Slots |
| PCI-Express | - 1 (x16) PCI-e slot (intended for Graphics applications)
- 1 (x4) PCI-e slot (using a x8 physical slot)
- 1 (x1) PCI-e slot
|
| PCI | 4x 32-bit 33MHz PCI (5V) slots |
| |
System BIOS |
| BIOS Type | 8Mb Flash EEPROM with Phoenix BIOS |
| BIOS Features | - Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0 (limited)
- USB Keyboard support
- SMBIOS 2.3
|
| |
Management |
| Software | - SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations | - ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard wakeup from soft-off
- Suspend to RAM (STR)
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
|
| |
PC Health Monitoring |
| Voltage | - Monitors for CPU Cores, +1.8V, +3.3V, +5V, ±12V, +3.3V/+5V Standby, VBAT
- CPU core 3-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio settings (via BIOS)
|
| FAN | - Total of three 4-pin fan headers
- 3x fans with tachometer monitoring
- Status Monitor with firmware/software speed control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connector
|
| Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor 2 (TM2) Support
|
| LED | - CPU / System Overheat LED
- +3V standby alert LED
- Supsend-State Indicator LED
|
| Other Features | - Chassis intrusion detection
- Chassis intrusion header
|
| |
Operating Environment / Compliance |
| RoHS | RoHS Compliant 6/6, Pb Free |
| Environmental Specifications | - Operating Temperature: 10° to 35 °C (50° to 95 °F)
- Non-operating temperature: -40° to 70 °C (-40° to 158 °F)
- Operating relative humidity: 8% to 90% (non-condensing)
- Non-operating relative humidity: 5 to 95% (non-condensing)
|
| |
OS compatibility |
| Please see our OS Compatibility Chart |
| |
Regulatory |
| FCC | Class B |
0 Articoli
